Heel and toe hooks are not “advanced tricks” or “gymnastics moves.”
Mechanically, they are lever systems that:
- redirect force
- extend your base of support
- stabilize the CoM
- reduce arm load
- create rotational counterforce
- increase reach
- anchor the kinetic chain on steep terrain
When used correctly, a heel or toe hook completely changes the geometry of a move.
This chapter breaks down the mechanics behind why hooks work — and why they fail.
1. Hooks Are Lever Systems, Not Grips
A hook is not about “gripping” with the foot.
It is about creating a lever arm through the leg that:
- generates counterforce
- stabilizes rotation
- increases friction
- transfers load into the hips
- frees the hands
Mechanically, the foot acts as an anchor while the leg produces torque.
This is why even a “bad” heel hook can feel unbelievably strong when the lever is aligned.
2. The Three Mechanical Functions of Hooks
Both heel and toe hooks can serve any combination of:
1. Counterforce creation
They oppose the direction of your pulling force, stabilizing the CoM.
2. Rotational control
They prevent the hips from swinging outward or collapsing.
3. Body positioning
They allow the hips to move closer to the wall or upward.
Hooks are force-directing tools — not just “extra hands.”
3. Heel Hooks: The Force Comes From Hip Extension
The power of a heel hook does not come from your hamstrings alone.
It comes from the hip extending backward, which generates torque through:
- glutes
- hamstrings
- obliques
- lower back
- core
- scapular stabilizers
The leg is the lever;
the hip is the motor.
A bent or passive hip eliminates the lever and makes the heel feel weak.
4. Toe Hooks: The Force Comes From Hip Flexion + Lateral Torque
Toe hooks do not rely on “curling your toes.”
They rely on:
- hip flexion
- hip abduction
- hip rotation (internal or external)
- engagement of the tibialis and anterior chain
Toe hooks are pulling hooks, not pushing hooks.
They work best when:
- your hips pull upward
- your torso rotates into the hook
- the vector matches the hold’s surface
When a toe hook rips off, the issue is almost always vector mismatch — not strength.
5. Hooks Change the CoM Path
Hooks fundamentally re-route your CoM trajectory.
Examples:
- A heel hook under a roof pulls your hips upward toward the wall.
- A toe hook on a sidewall pulls your torso inward, reducing swing.
- A high heel on a volume boosts your CoM vertically with almost no arm effort.
- A toe hook under a lip locks the CoM in place for a controlled reach.
Hooks are not “holds” — they are CoM steering mechanisms.
6. Hooks Work Only When the Force Vector Is Perpendicular to the Surface
Same physics as slopers:
Friction is maximized when force is applied perpendicular to the surface.
Heel hooks fail when:
- the knee drifts outward
- the torso rotates away too early
- the heel pushes instead of pulling
- the hip angle collapses
- the CoM moves too far outward
Toe hooks fail when:
- the rotation is wrong
- hips rise before tension engages
- the hook pulls in the wrong direction
- the shin is not aligned with the surface angle
Strength cannot overcome a bad vector.
7. Hooks Reduce Arm Load Drastically
A good hook can:
- remove 30–70% of load from the hands
- keep slopers usable
- maintain tension during big reaches
- control swing before it starts
- allow resting positions even on steep terrain
This is why expert climbers look relaxed where beginners look desperate:
Hooks create structural support, making muscles secondary.
8. Heel Hooks Increase Reach via Hip Rotation + Levering
A heel hook changes body geometry:
- the hip rotates inward
- the torso closes to the wall
- the leg pulls the pelvis higher
- the shoulder enters a stronger lock-off angle
This gives:
- more reach
- more stability
- a safer catch zone
You don’t reach farther because you stretch.
You reach farther because leverage changes.
9. Toe Hooks Provide Rotational Counterforce
A toe hook acts as an opposing torque generator.
Mechanics:
- torso rotates one way
- toe hook pulls the opposite way
- rotational momentum cancels
- swing stops
- the CoM stabilizes
This is why toe hooks are essential in:
- coordination moves
- steep compression
- crossing moves
- matching big volumes
- resisting outward swing after a deadpoint
Toe hooks are not optional — on steep terrain, they are essential.
10. Exit Mechanics: The Hook Must Release Smoothly
Hooks fail during exit when:
- tension drops too fast
- hips rise before the hook disengages
- the new foothold is weighted too quickly
- the next hand move begins prematurely
Correct exit sequence:
- create a new base of support
- gradually release hook tension
- follow the torque path into the next position
- re-engage the kinetic chain
- only then move hands or feet
Hooks are not just “on/off.”
They must be ramped in and ramped out.
The Rule: Hooks Create Leverage — Leverage Determines Stability
Hooks succeed when they:
- match the force vector
- engage the hips
- steer the CoM
- generate counterforce
- stabilize rotation
- create predictable leverage
Hooks fail when:
- the vector mismatches
- the hip collapses
- rotation is uncontrolled
- the CoM drifts outside the support zone
Strength is irrelevant without leverage.