Climbers often think injuries come from “too much weight” or “bad technique.”
But the real cause is almost always the interaction between three variables:
- Force (how much load)
- Time (how long the load lasts)
- Tissue stress (how the load is distributed through structures)
These three form a single mechanical system.
When one variable gets out of balance, tissue stress spikes — and that’s when injuries happen.
This article explains the simplest possible model for finger injury risk and performance.
1. Force: the load your finger is holding
Force is the most obvious variable, but also the most misunderstood.
Force includes:
- your bodyweight
- added hangboard load
- angle amplification from grip position
- acceleration forces during dynamic moves
- sudden “shock loads” when catching holds
Force is never just weight.
Small edges + sharp angles multiply the force internally, even if the external load doesn’t change.
And in climbing:
👉 most injuries happen without high external force, but with high internal force.
2. Time: the duration your tissues must handle the load
Time determines whether tissues can maintain stability.
Two extremes matter:
Short-duration, high-force
- max hangs
- full crimp on micro edges
- dynamic deadpoints
- sudden load shifts
These challenge the structural limits (pulleys, tendon tension).
Long-duration, moderate-force
- repeaters
- pumpy climbing
- hanging too long on holds
- technique breakdown under fatigue
These challenge the endurance limits (joint stability, capsules, tendon gliding).
The key principle:
👉 Short efforts break structures.
👉 Long efforts break mechanics.
Both lead to injury, but through different failure modes.
3. Tissue stress: where the force actually goes
Even if force and time are identical, the distribution can vary massively depending on:
- joint angles
- pulley tension
- tendon curvature
- wrist alignment
- hold size
- grip type
- fatigue level
This determines:
- how much load reaches A2
- how much is transmitted through FDP
- how much FDS contributes
- how stable the PIP angle is
- whether bowstringing occurs
Tissue stress is the internal load — the only load the body actually experiences.
This is why mechanical form matters more than weight.
4. The injury triangle: Force × Time × Stress
Injury risk spikes when:
1) Force is high
e.g. full crimp, tiny edges, weighted hangs.
2) Time is long
e.g. failing to let go when tired, dogged redpoints.
3) Stress distribution is unstable
e.g. collapsing joints, DIP unrolling, sudden catches.
When two variables spike, the risk rises sharply.
When all three spike, injuries are almost guaranteed.
Examples:
- Full crimp + small edge + fatigue → A2 overload
- Open hand + drag collapse + heavy load → FDP distal overload
- Dynamic catch + poor angle + cold fingers → pulley shock load
- Long pumpy climb + angle drift + small holds → capsule/collateral irritation
The triangle explains every common finger failure.
5. Why structured progression works mechanistically
Because it keeps Force, Time, and Stress inside adaptable ranges.
Slow force progression
→ tissues adapt
→ pulleys thicken
→ tendons handle tension
→ joints remain stable
Controlled time under tension
→ improves stability
→ prevents joint drift
→ reduces fatigue collapse
Consistent mechanics
→ reduces unexpected stress spikes
→ keeps tendon curvature predictable
→ maintains the force line
Training works not by adding weight, but by controlling geometry.
6. Why chaotic climbing causes more injuries
Chaotic = random grip types, random angles, random load patterns.
The triangle becomes unpredictable:
- unpredictable forces
- unpredictable stress distribution
- unpredictable time under tension
This forces passive tissues to compensate:
- joint capsules
- collateral ligaments
- volar plate
- pulleys
Chaotic load → chaotic stress → injury.
7. Practical rules that emerge from the model
Rule 1 — Increase load gradually (Force control)
2–5% progression keeps tissues in the adaptive zone.
Rule 2 — Stop when technique collapses (Time control)
Fatigue = angle drift = increased stress.
Rule 3 — Train on safe edges (Stress control)
15–20 mm is optimal for 95% of training.
Rule 4 — Reduce grip variation when training fingers
Consistency = predictable forces = predictable stress.
Rule 5 — Warm up long enough to stabilize tissues
Cold fingers = stiff capsules = high stress sensitivity.
Rule 6 — Use small edges as testing tools, not training tools
Small edges amplify all variables.
Putting it all together
Every finger injury — pulley, tendon, capsule, ligament — can be explained by:
- too much force
- for too long
- with unstable mechanics
The Force–Time–Stress model is the simplest way to understand:
- why injuries happen
- why progression works
- why some sessions feel risky
- why technique matters more than strength
- why finger training needs predictability
Master these three variables, and you don’t just climb harder —
you climb consistently, safely, and with predictable adaptation.